Assembly instructions
10Operate as follows:•Unwind the electric cable and connect it directly tothe wall socket.•Make sure the appliance is in the Stand-by conditionand tha
11The dimensions of the panels are indicated in the table and drawings on pages 18-21.Nevertheless, according to the requirements for aligning with ot
12•Position the brackets on each set of marks to makesure they are aligned 4, then drill holes through thepanel (pay close attention to the panel’s th
13Preparing the decor panels for the built-in RefrigeratorHolespositions90cm 75cm 60cmHingeLeft HingeRight HingeLeft HingeRight HingeLeft Hinge
14Doorwindowdimensions HolespositionsPreparing the decor panels for the built-in Refrigerator with glass door90cm 60cmHingeLeft HingeRight Hinge
15Dimensions of built-in panelsSeries Door/DrawerWidthA DoorCutoutWidthB90cm897 (35 1/4”) 627 (24 3/4”)75cm747 (29 3/8")60cm597 (23 1/2”) 32
16Once all brackets and small brackets have been appliedto the panels, you can begin installing the bottomdrawer.Operate as follows:•Partially tighten
17•Hook the panel to the fixing devices starting from thetop aligning brackets 6.•At this point, alignment between the panel andadjacent cabinets can
18InstallationBuilt-in installation single applianceFor a built-in installation, to close gaps between the appliance and the adjacent cabinets, specia
19InstallationBuilt-in installation two or more appliancesRequired accessories to be ordered separately: •Central connection KitSpecial side profiles
20•Once completed the previous steps, push the units intheir final position 6.If the units are to be installed inside a niche or withinan enclosed str
21InstallationFree-standing installation two or more appliancesRequired accessories to be ordered separately:•Central Connection Kit•Freestanding KitA
22•Attach the side panels to the unit, mounting them onthe side profiles 7 pre-mounted on the unit.•Attach the aluminum cover 8 to each side profile,p
23To prevent the appliance from tipping over an extra-long kit is vailable up on request if the appliance needsto remain distanced from the wall, it i
24A forced air system assures ventilation through a grillepositioned in the lower front part of the unit. If thekitchen design includes a kickplate, t
25•Check that the front levelling feet have been properly installed.•Check that the connection to the water system does not have any leaks and that th
Printed in Italyr 09/16400011044720EN
Important safely instruction 4Children safety 4Characteristics of the appliance and installation requirements 5Installation niche features: built-in 6
4Symbols used in the GuideNoteTips for the correct use of the applianceImportantDirections to avoid appliance damageWarningdirections to prevent injur
5DimensionsofBuilt-in/Integratedappliance60cm: l: 587 mm (23 1/8” in)/ h: 2050 mm (80 3/4” in)/ w: 575 mm (22 5/8” in)75cm: l: 737 mm (29” in)/ h:
6A: area to be left clear for the anti-tipping bracketsE: area to be left clear for the power supply cableW: and water supply hoseMinimumNicheHeight
7A: area to be left clear for the anti-tipping bracketsE: area to be left clear for the power supply cableW: and water supply hoseMinimumNicheHeight
8Transport to installation site and unpackingSince this is a large and heavy appliance, before transporting the appliance, check the access to the loc
9Electrical connection requires use of a European 16ASchuko socket or UK 13A socket with earth connection,controlled by an easily accessible omnipolar
Kommentare zu diesen Handbüchern